SUBMIT A REQUEST
Follow

Configuration using the web interface

 

The below instructions are available for units running latest firmware version 3.1.9.
Some information might vary if yours run an older version. 

 

The Gramofon web interface is one of the 2 available tools to set up Gramofon, in this case from a computer. If you don't possess any computer, or simply you prefer to use a mobile device, please check out this article instead.

The Gramofon can connect to the internet through an existing WiFi network or via cable. 

This article explains how to configure the Gramofon using these 2 different ways (via WiFi or via cable), and afterwards access its settings, for Gramofons running firmware version 3.1.9

 

Configuration

IMPORTANT: If your Gramofon has never been configured (in Easy Set up mode), you will be able to start directly with the configuration process. On the contrary, if your Gramofon is already configured and you wish to modify its configuration, you will have to open the Gramofon Setup app, detect your connected Gramofon and look for its local IP. If you can't use the Gramofon Setup app, then just perform a factory reset before starting with the re-configuration process.

Start by accessing your new Gramofon’s web interface. You can do it via WiFi or using the Ethernet cable (Gramofon computer port to computer).

Power up your Gramofon and use a computer or mobile device to connect to the private WiFi signal "Gramofon Configuration", open your browser and type http://192.168.10.1* (if your Gramofon has been reset to factory settings) or http://local IP as shown in Gramofon Setup app (if your Gramofon is already registered) into the address bar. You can also simply plug the Ethernet cable from the Gramofon computer port to your computer.

Then log in with the Gramofon's password, the default is admin

Note (*): 192.168.10.1 is the Gramofon's default IP address. 

 

WiFi connection

Once logged in, the first page will display the name of the Gramofon available for the configuration, and offer you the option to modify it. Click "Next" to continue with the configuration process.

The following screen will show the "WIFI" tab. Click "Next" if you wish to configure your Gramofon in this mode.

The option "Extend my home WiFi signal" will clone (duplicate) your home WiFi signal. This can be very useful if some areas are not in range of your home router, as you would simply need to place the Gramofon between your home WiFi router and the WiFi dead zone to extend your home WiFi.

In this case, tick the checkbox, select the wireless network the Gramofon is going to join in order to access to the internet (Home WiFi Name), and introduce the corresponding password (WPA or WPA2, remember WEP encryption is not compatible). 

If you don't wish to extend your home WiFi signal, simply untick the checkbox and follow the same procedure. 

 

Click on "Finish" to apply the configuration. It's done! Your Gramofon is now connected to the internet via WiFi.

If this is not the case, please refer to Troubleshooting.

 

Note: if your home router main WiFi signal is hidden, as it will not appear in the list of WiFi signals available, you will have to scroll down to the very bottom and select the "Custom" option.

Then simply introduce the hidden SSID exact name, the corresponding password, and click on "Finish" to apply the configuration. 

Back to top

 

Cable connection

Once logged, the first page will display the name of the Gramofon available for the configuration, and offer you the option to modify it. Click "Next" to continue with the configuration process.

The following screen will show the "WIFI" tab. Click on the "CABLE" tab and then "Next" if you wish to configure your Gramofon in this mode.

Plug an Ethernet cable (supplied) from your broadband router to the Gramofon.

Cable mode offers the option to create a separate WiFi signal to which you will connect to stream your music.

If you wish to use this option, just tick the chechbox "Create new signal for my home"*. You will be invited then to name it and choose a password (between 8 and 63 alphanumeric chars). 

Click on "Finish" to apply the configuration. It's done! Your Gramofon is now connected to the internet via cable.

*If you don't wish to create a new WiFi signal, simply untick the checkbox and click on "Finish". 

If this is not the case, please refer to Troubleshooting.

Important Note: Please consider that WiFi performance can be affected by environmental factors such as the thickness and proximity of walls, or interface from other devices such as microwaves or wireless telephones, and choose the location of the Gramofon accordingly.

Back to top

 

Access the Settings

Power up your Gramofon and use a computer or mobile device to connect to the WiFi signal to which your Gramofon is connected, open your browser and type the Gramofon IP into the address bar. 

An easy way to know your Gramofon IP is using the Gramofon Setup app

Then log in with the Gramofon's password, the default is admin

The home page shows the status of your Gramofon, and gives the option to modify or switch set up mode (connection type). If you wish to modify the settings of the current set up mode, click on the "Internet Settings" button of the current tab. And if you wish to change the set up mode, then just click on the other available tab (here in the example, we would switch from WiFi to Cable mode) and follow the on-screen instructions. 

Click on the menu icon at the top right corner of the screen, to get access to advanced settings, rename your Gramofon and log out.

Advanced settings enable you to modify the password of the web interface (default is admin), reboot the Gramofon and restore its factory settings, and see the current firmware version.

Finally, you'll be able to modify the Gramofon name. Remember to click on "Save and Apply" to confirm the change.

 

Back to top

 

Powered by Zendesk